How to replace garbage disposal hardwired

If you have a dishwasher, turn it on and check that connection. Inspect every area to ensure that there is no leakage. Turn on the faucets and let the water flow through the disposal. The disposal should now be locked into place.Р вЂќР Р‹3. Tighten the collar down with a screwdriver or wrench. There is a rotating cam collar near the mounting assembly. Once the plumbing is connected, make sure that all of the nuts are tight and that the disposal line is secure. Remember to slide the lock nut on the pipe before the nylon washer.Р вЂќР Р‹2.

Cut some PVC plumbing pipes so that the connection fits properly. Your 'J' trap will probably not line up perfectly with the disposal, especially if you have a double-bowl sink. If you have a dishwasher, connect the drain line to the inlet port on the side of the disposal. Shift your disposal so thatР вЂ™Р’В the discharge tubeР вЂ™Р’В lines up with the water pipes. After it is locked it will still be a bit loose. This may be a bit frustrating, but be patient. Once theР вЂ™Р’В tabs are into the mounting assembly, turn the disposal so that it locks into place. There are threeР вЂ™Р’В tabs on the disposal that help it lock into the mounting assembly. Line it up with the mounting assembly under the sink. The plug may fall into your disposal, so be sure that you get it out before proceeding.Р вЂќР Р‹0. Take out the line plug with a screwdriver and a hammer. This is where the dishwasher inlet line is connected.

Find the close-ended tube on the side of the disposal, near the top. If you happen to have a dishwasher then there is an extra step in the process. Next ground the supply wire and replace the electrical cover plate on the unit.Р вЂќР’В©. Rest the disposer on its side underneath the sink.Р вЂ™Р’В After shutting off the breaker, you need to remove the disposal's cover plate to access the wiring.Р вЂ™Р’В Connect the white and black wires to the matching wires from the power supply. Plumbers putty will most likely emerge from under the flange, but there's no need to worry just wipe away the excess.Р вЂќР Рѓ. Alternate between the three bolts, and make sure that they are evenly tightened. Locate the three mounting bolts and begin tightening them. Now it's time to tighten the mounting bolts. Connect the snap ring to the flange, which will keep the gasket and ring in place.Р вЂќР’В§. Take the gasket and the mounting ring andР вЂ™Р’В push them up the flange. Find your gasket and mounting ring and head back under the sink. Next, take the sink flange,Р вЂ™Р’В place it in the drain and press it down carefully onto the putty.Р вЂќР’В¦. Open up your plumbers putty andР вЂ™Р’В place a quarter-inch coilР вЂ™Р’В of putty around the drain. The mounting assembly includes upper and lower mounting rings and mounting bolts. First off, you will need the sink flange and the mounting assembly. Now you can open your new garbage disposal and begin installing it. You want the surfaces to be nice and clean.Р вЂќРўС’. Remove the strainer and make sure to clear away anyР вЂ™Р’В pre-existing plumbers putty from around the area. You should see a large nut that is securing the strainer.

Once the waste linesР вЂ™Р’В are removed, you need to remove the mounting assembly. Empty all of the excess water into the bucketР вЂќР в‚¬. Place your bucket under the sink and remove the wastelines. The first task is to disconnect and remove the strainer and all of waste drain lines from the sink.Р вЂќРЎС›. Clear everything from under your sink so that there is room to operate.

How to replace garbage disposal hardwired